Escolha uma Página

EP-ZQ60 IBM Machine — Replacement for SUMA 65iB

Máquina de Moldagem por Injeção e Sopro ZQ60

EP-ZQ60 is a 3-station European injection blow molding machine rated at 600 kN injection clamping — 3.4% above SUMA 65iB-class 580 kN — and 383 g maximum injection weight (50 mm screw), 45% above the SUMA 65iB maximum of 264 g (50 mm screw). Machine height 1.8 m versus SUMA 65iB 2.3 m (−22%); width 1.4 m versus 1.7 m (−18%); length 3.8 m versus 4.0 m (−5%). EP-ZQ60 is smaller in every dimension while delivering higher clamping force and substantially higher shot weight. Up to 14 cavities at 10 ml, 8 cavities at 100 ml. Dual screw 45 mm (260 g) or 50 mm (383 g). Processes PP, PCTG, HDPE, LDPE, PS, ABS, EVA, PLA. S136 SPI A1 mould: PCTG haze below 2%. Dry cycle 3.5 s, total power 37 kW, weight 5 T. CE + ISO 9001:2015. Brand references for buyer selection convenience only; Korea Ever-Power is not affiliated with SUMA Co., Ltd.

Categoria:
Consulte agora

Selection Reference Notice: "SUMA" and "65iB" are trademarks of SUMA Co., Ltd. (Taiwan), referenced solely to help buyers identify the Korea Ever-Power EP-ZQ60 as a comparable alternative. Korea Ever-Power does not manufacture, distribute or represent SUMA products. All technical data below refers exclusively to the Korea Ever-Power EP-ZQ60.

Visão geral do produto

O Korea Ever-Power EP-ZQ60 matches the SUMA 65iB in tonnage class but outperforms it on every production metric that determines cost per bottle. At 600 kN injection clamping versus SUMA 65iB 580 kN, the clamping difference is modest (3.4%). The injection weight gap is not: EP-ZQ60 at 383 g with the 50 mm screw delivers 45 percent more shot weight than the SUMA 65iB maximum of 264 g — and that 119 g difference directly translates into additional cavities, heavier-wall formats, and higher-MW resins that the SUMA 65iB cannot accommodate at this clamping class.

Máquina de Moldagem por Injeção e Sopro ZQ60

The physical dimensions tell the same story in reverse: EP-ZQ60 is smaller than the SUMA 65iB in all three dimensions. At 3.8 × 1.4 × 1.8 m versus SUMA 65iB 4.0 × 1.7 × 2.3 m, the EP-ZQ60 is 18% narrower and 22% shorter, fitting Korean pharmaceutical GMP cleanrooms with 2.4 m ceiling clearance where SUMA 65iB at 2.3 m leaves only 0.1 m overhead — insufficient for barrel maintenance access.

The full máquina de moldagem por injeção e sopro range spans EP-ZQ40 through EP-ZQ135 for every production scale.

EP-ZQ60 vs SUMA 65iB — SIZE & PERFORMANCE AT A GLANCE

Grampo de injeção
600 kN
vs 580 kN (+3.4%)
Max Shot
383 g
vs 264 g (+45%)
Altura
1.8 m
vs 2.3 m (−22%)
Width
1.4 m
vs 1.7 m (−18%)
Cáries @10ml
14
8 cavities @ 100 ml
Potência Total
37 kW
3.5 s dry cycle

Especificações técnicas

EP-ZQ60 IBM machine internal structure 600kN 3-station simultaneous cycle Korea Ever-Power SUMA 65iB replacement

All parameters sourced from Korea Ever-Power ZQ60 product specification data. Screw selection (45 mm or 50 mm) confirmed against your resin MFR and preform weight at quotation stage.

Sistema de Injeção
Diâmetro do parafuso45 / 50 mm
Relação L/D22 : 1
Peso da Injeção260 / 383 g
Potência de aquecimento10 kW
Heating Zones3 + N
Fixação
Inj. Clamp Force600 kN
Inj. Open Stroke200 mm
Blow Clamp Force90 kN
Blow Open Stroke170 mm
Table Lift80 mm
Strip Stroke260 mm
Mould & Output
Platen (L × W)600 × 390 mm
Espessura do molde220 mm
Max Bottle Dia.150 mm
Altura máxima da garrafa260 mm
Faixa de volume1 – 2000 ml
Ciclo de secagem3.5 s
Power & Machine
Potência do motor22 kW
Potência Total37 kW
Hydraulic Press.14 MPa
Air0.7–1.2 MPa / 1.0 m³/min
Cooling Water5.0 m³/h
L × W × H3,8×1,4×1,8 m
Peso5 T

Max Cavity Count by Bottle Volume — EP-ZQ60

10 ml 30 ml 60 ml 100 ml 250 ml 500 ml 1000 ml
14 12 10 8 5 3 2

For reference only. Source: Korea Ever-Power ZQ60 product specification data.

EP-ZQ60 vs SUMA 65iB — Parameter Comparison

EP-ZQ60 IBM mould tooling 600x390mm platen Korea Ever-Power SUMA 65iB replacement S136 SPI A1 crystal-clear PCTG

Korea Ever-Power ZQ60 catalogue data versus SUMA 65iB-class reference figures from the Korea Ever-Power IBM competitor analysis report. SUMA data cited for buyer selection convenience only; Korea Ever-Power does not guarantee its accuracy.

Parâmetro EP-ZQ60 SUMA 65iB (Ref.) Difference
Injection Clamp Force 600 kN 580 kN +3.4%
Diâmetro do parafuso 45 / 50 mm 40 / 50 mm 45mm std option
Max Injection Weight 260 / 383 g 169 / 264 g +45% (383 vs 264)
Mould Platen (L × W) 600 × 390 mm 620 × 400 mm Similar area
Machine Length 3.8 m 4.0 m −5%
Machine Width 1.4 m 1.7 m −18%
Machine Height 1.8 m 2.3 m −22%
Peso da máquina 5 T — (not published) —
Potência Total Instalada 37 kW — (not published) 10–20% less/cycle
Ciclo de secagem 3.5 s — (not published) —
PCTG SPI A1 Option S136 — haze < 2% Standard tooling Luxury grade
Certification CE + ISO 9001:2015 CE Equal

Buyers evaluating other SUMA iB models will find dedicated EP-ZQ40 vs 40iB, EP-ZQ80 vs 85iB, EP-ZQ110 vs 135iB and EP-ZQ135 vs 175iB comparison pages in the IBM machine replacement guide.

Why EP-ZQ60 Over SUMA 65iB

01
45% Higher Shot Weight — 383 g vs SUMA 65iB 264 g at 50mm Screw

Both EP-ZQ60 (50 mm screw option) and SUMA 65iB (50 mm screw option) offer a 50 mm screw, yet EP-ZQ60 achieves 383 g versus SUMA 65iB 264 g — a 45 percent shot weight advantage at the same screw diameter. This reflects differences in barrel L/D ratio and injection stroke. Practical consequence: for 100 ml pharmaceutical PP bottle at 30 g per preform, EP-ZQ60 at 383 g runs 8 cavities (240 g within limit); SUMA 65iB at 264 g can run 8 cavities (240 g, marginally within limit). At 35 g per preform (heavier-wall grade): EP-ZQ60 runs 8 cavities (280 g within 383 g); SUMA 65iB at 264 g is limited to 7 cavities (245 g). Every additional cavity directly increases output without increasing machine cost, cycle time or energy consumption.

02
Smaller in All Three Dimensions — Yet Higher Clamp and Larger Shot

EP-ZQ60 is 5% shorter in length, 18% narrower and 22% lower in height than SUMA 65iB — while delivering higher clamping force and substantially more shot weight simultaneously. This is the defining advantage of the European pressurised-clamping architecture: the booster cylinder does not need the structural frame space that SUMA 65iB-class hydraulic main-cylinder designs require for open/close travel clearance. For Korean pharmaceutical GMP cleanroom buyers and daily chemical manufacturers where factory floor cost per square metre is a real constraint, a machine that is smaller, lighter and more capable simultaneously is unambiguously the correct choice.

03
1.8 m Height — Korean GMP Cleanroom Compliant; SUMA 65iB 2.3 m Is Not

Standard Korean pharmaceutical GMP cleanroom ceiling height is 2.4–2.7 m. SUMA 65iB at 2.3 m leaves only 0.1–0.4 m overhead clearance — below the 0.5 m minimum typically required for barrel heater element removal and replacement above the heating zone. EP-ZQ60 at 1.8 m leaves 0.6–0.9 m clearance in the same cleanroom. This is not a marginal difference: it determines whether a machine passes the facility installation qualification (IQ) protocol for a new pharmaceutical packaging GMP programme without requiring ceiling modification works.

04
S136 SPI A1 Mould Option — PCTG Haze < 2%, Luxury K-Beauty Grade

SUMA 65iB-class standard mould tooling uses H13 tool steel which cannot achieve PCTG haze below 2% at the Ra ≤ 0.010 μm surface finish required by Korean luxury K-beauty cosmetic serum vial brands. Korea Ever-Power EP-ZQ60 offers S136 stainless SPI A1 injection cavities and blow moulds as a standard upgrade, delivering 0.8–1.6% ASTM D1003 haze at 0.5–0.6 mm body wall on PCTG Eastman TX1001. At 14 cavities per cycle for 10 ml PCTG eye serum droppers, EP-ZQ60 with S136 SPI A1 tooling produces 14,000–14,400 crystal-clear bottles per hour at a quality grade SUMA 65iB-class cannot match.

05
10–20% Lower Energy Per Cycle — European Pressurised-Clamping Design

EP-ZQ60 booster cylinder provides 600 kN injection clamping hold force without participating in mould open/close travel — the defining mechanical efficiency advantage of European IBM architecture. Conventional SUMA 65iB-class design uses the main hydraulic cylinder for both clamping force and open/close travel, accelerating and decelerating on every cycle. EP-ZQ60 total installed power at 37 kW with 55–70% steady-state utilisation delivers 10–20% lower energy per cycle versus conventional IBM designs of equivalent clamp tonnage. Over three-shift Korean pharmaceutical production, this difference accumulates to a measurable annual electricity cost reduction per installed machine.

Application Scenarios

Tipos de Garrafa-2

💊
Pharmaceutical IBM

PP and HDPE tablet bottles, syrup bottles, oral suspension and eye dropper vials. 30–500 ml at 5–10 cavities. EP-ZQ60 at 383 g shot runs 8 cavities at 100 ml vs SUMA 65iB at 264 g limited to 7 at heavier-wall formats. Korean MFDS, FDA 21 CFR, EU GMP documentation available.

✨
K-Beauty Luxury Cosmetic

PCTG crystal-clear eye serum droppers, essence vials, nail oil dropper and BB cream pump bottles. S136 SPI A1 mould option: 0.8–1.6% ASTM D1003 haze, glass-look surface. 14 cavities at 10 ml = 14,000+ bottles/hr. SUMA 65iB-class H13 tooling cannot reach this optical grade.

💧
Daily Chemical & Fragrance

PP and PCTG shampoo, body wash, fragrance body mist and hand sanitiser bottles. 50–500 ml at 3–8 cavities. 383 g shot supports 5-cavity 500 ml PP shampoo at 55 g per bottle (275 g total) — within EP-ZQ60 limit; exceeds SUMA 65iB 264 g maximum at 5 cavities.

🌿
Food Supplement & Health

PP and HDPE supplement capsule, probiotic and vitamin container IBM at 60–500 ml in 3–10 cavity configurations. Korea Ever-Power supplies food-contact documentation package (Korean MFDS, FDA 21 CFR 177.1520 for PP, EU 10/2011) at programme commencement.

EP-ZQ Series Selector

All data sourced from Korea Ever-Power ZQ-series product specification catalogue. SUMA model designations are cited for buyer reference only.

Parâmetro EP-ZQ40 EP-ZQ60 EP-ZQ80 EP-ZQ110 EP-ZQ135
Grampo de injeção 400 kN 600 kN 800 kN 1,100 kN 1,350 kN
Max Shot 190/260 g 260/383 g 466 g 540 g 650 g
Height (m) 1.7 1.8 2.0 2.2 2.4
Cáries @10ml 9 14 20 24 30
Cavities @100ml 4 8 12 14 18
Potência Total 20 kW 37 kW 55 kW 80 kW 95 kW
SUMA Equivalent 40iB 65iB 85iB 135iB 175iB

Source: Korea Ever-Power ZQ-series product specification data. SUMA iB designations are for buyer reference only.

Perguntas frequentes

Q1: Will existing SUMA 65iB mould tooling fit the EP-ZQ60?

Not without assessment. SUMA 65iB platen is approximately 620 × 400 mm versus EP-ZQ60 600 × 390 mm — dimensions are close but mandrel pitch, mould thickness (220 mm on EP-ZQ60) and bolt-hole patterns differ. Send SUMA 65iB mould base drawings for a Korea Ever-Power compatibility assessment within 5 working days at no cost.

Q2: How can EP-ZQ60 achieve 383 g at 50 mm screw when SUMA 65iB at 50 mm screw reaches only 264 g?

At identical screw diameter, injection weight is determined by L/D ratio and effective injection stroke. Korea Ever-Power EP-ZQ60 uses a 22:1 L/D ratio with a longer effective injection stroke than SUMA 65iB-class, resulting in 383 g at 50 mm versus SUMA 65iB 264 g at the same screw diameter. The 45% shot weight advantage at equal screw diameter reflects these internal barrel design differences and is a fundamental capability difference between the two machine architectures.

Q3: What is the EP-ZQ60 machine and mould lead time?

Machine: 50–65 working days from order confirmation and deposit. Mould tooling: 40–50 working days (H13 SPI B1) or 55–70 working days (S136 SPI A1). Machine and mould manufactured in parallel for simultaneous T1 trial commissioning before shipment.

Q4: Can EP-ZQ60 install in a Korean pharmaceutical GMP cleanroom where SUMA 65iB cannot?

Yes, in most standard Korean pharmaceutical GMP cleanroom configurations. SUMA 65iB at 2.3 m height leaves only 0.1 m overhead clearance in a 2.4 m ceiling cleanroom — below the minimum required for barrel heater element service (approximately 0.5 m above heater bands). EP-ZQ60 at 1.8 m leaves 0.6 m clearance in the same environment. This difference determines whether the machine passes GMP facility IQ protocol without ceiling modification works costing 30–80 million KRW.

Q5: How many cavities does EP-ZQ60 support for 30 ml PCTG cosmetic serum dropper vials versus SUMA 65iB?

From the Korea Ever-Power ZQ60 cavity table: 12 cavities at 30 ml format on EP-ZQ60. SUMA 65iB-class cavity data is not published in Jomar/SUMA technical literature for direct comparison, but shot weight ceiling of 264 g at 50 mm screw constrains maximum cavity count at typical 30 ml PCTG preform weights of 15–18 g. At 18 g per preform: SUMA 65iB at 264 g supports at most 14 cavities (252 g within limit). At 20 g per preform: EP-ZQ60 at 383 g supports 12 cavities (240 g within limit and confirmed from cavity table); SUMA 65iB at 264 g supports 13 cavities (260 g, marginally within limit). At heavier-wall 30 ml PCTG at 22 g per preform: EP-ZQ60 at 383 g runs 12 cavities (264 g); SUMA 65iB at 264 g is limited to 11 cavities (242 g). The EP-ZQ60 cavity table figure of 12 cavities at 30 ml is the confirmed Korea Ever-Power specification.

Q6: What GMP documentation does Korea Ever-Power provide for the EP-ZQ60?

Machine data sheet; FAT report on buyer-specified resin and cavity format; CE certificate; ISO 9001:2015 certificate; PP resin CoA with Korean MFDS food container registration and KP plastic container standard test from KOLAS-accredited laboratory; PCTG Eastman TX1001 FDA 21 CFR 177.2490 food contact letter + EU 10/2011 Declaration of Conformity. IQ/OQ documentation template on request.

Q7: What after-sales service does Korea Ever-Power provide in Korea?

One week on-site commissioning and operator training at buyer's facility. 24/7 remote PLC VPN diagnostic support for 90 days post-commissioning, 2-hour software response SLA. Korea Ever-Power Ansan-si, Gyeonggi-do service base maintains spare parts inventory for same-day Korean dispatch. Scheduled preventive maintenance visits available on annual service contract.

Q8: What PCTG optical quality does EP-ZQ60 achieve with S136 SPI A1 tooling?

0.8–1.6% ASTM D1003 integrating sphere haze at 0.5–0.6 mm body wall, verified on Korea Ever-Power ZQ-series T1 trials with PCTG Eastman TX1001 at 252 °C barrel and 20 °C blow mould cooling. SUMA 65iB-class standard H13 tooling typically achieves 3–5% haze at comparable wall — above the 2% threshold for Korean luxury K-beauty eye serum and nail oil dropper brands. The S136 SPI A1 option on EP-ZQ60 unlocks this premium cosmetic packaging segment that SUMA 65iB-class cannot qualify for.

Q9: Which EP-ZQ model is the correct replacement for SUMA 85iB?

EP-ZQ80 (800 kN, screw 55 mm, max shot 466 g, platen 800 × 400 mm, total power 55 kW, machine 4.5 × 1.6 × 2.0 m, 10 T) is the reference replacement for SUMA 85iB-class (720 kN, screw 50/60 mm, shot 333/480 g, platen 700 × 400 mm, footprint 4.5 × 2.0 × 2.6 m). Dedicated comparison page in the IBM machine replacement guide.

Q10: Does EP-ZQ60 carry CE marking for European pharmaceutical packaging market requirements?

Yes. CE marking including Declaration of Conformity to the relevant EU Machinery Directive is standard on every EP-ZQ60. European-destination units are configured for 400 V / 50 Hz at order stage. The CE documentation package is available for review before order confirmation on request.

Ready to evaluate EP-ZQ60 as your SUMA 65iB replacement?

Send Korea Ever-Power your bottle drawing, resin grade, required cavity count and annual production volume. We return a full feasibility report within 48 hours — EP-ZQ60 configuration, projected output per hour, mould tooling lead time and transparent quotation.

Informação adicional

Editor

Cxm

Produtos relacionados