HGA.ES-2C100 Medicine Bottle Blow Molding Machine – 2 Cavity | 500ml | 2400 BPH

HGA.ES-2C100

Fully Automatic Two-Step PET Stretch Blow Molding Machine for Pharmaceutical Bottles

2 Cavities · 500 ml Max · 2,400 BPH · 80mm Max Body · Korea Ever-Power

Why Choose the HGA.ES-2C100?

✓  Smallest footprint in the Medicine Bottle Series — 2,900 × 1,525 × 1,930 mm and 2,000 kg, fit for compact cleanroom and GMP workshop layouts.

✓  80 mm max body diameter — wider body than the 76.2 mm pitch AS-4C76.2, enabling standard pharmaceutical bottle profiles up to 80 mm that the compact-pitch 4-cavity machine cannot produce.

✓  Lowest utility consumption in the ES range — 8–12 kW normal heating and 1,000–1,400 L/min high-pressure air keep operating costs the lowest of the ES medicine bottle models.

✓  ES series servo architecture — next-generation servo-driven blow station delivering precise stretch-blow control and reduced mechanical wear versus earlier-generation cam-driven designs.

① Lightest Machine in the Series

At 2,000 kg and 2,900 × 1,525 × 1,930 mm, the HGA.ES-2C100 is the smallest and lightest machine in the entire Medicine Bottle Series — fitting production floors and cleanroom layouts where other models in the range would not. Standard floor loads apply without reinforcement in most facilities.

② 80 mm Body — Wider Than 76.2 mm Pitch Models

The 100 mm pitch supports containers up to 80 mm body diameter — 15 mm wider than the 76.2 mm pitch AS-4C76.2 allows. This covers the standard pharmaceutical bottle body range used in most regional pharmacy supply formats, including larger dropper and liquid medicine bottles.

③ Lowest Utility Consumption in ES Range

8–12 kW normal heating power and 1,000–1,400 L/min high-pressure air are the lowest utility requirements of any ES series medicine bottle machine. The reduced air consumption directly lowers compressor operating cost and simplifies the auxiliary equipment specification for smaller facilities.

④ ES Series Servo Architecture

The ES designation introduces Korea Ever-Power's servo-driven blow station architecture — delivering precise stretch-rod control, repeatable positioning, and reduced mechanical wear versus earlier cam-driven designs. Servo actuation also enables faster changeover between blowing parameters for different vial formats.

⑤ Adjustable Blowing Pressure Range

Blowing pressure is adjustable between 26–35 kg/cm², providing a wider tuning range than fixed-pressure configurations. This flexibility supports different PET/PETG/PP material grades and wall thickness targets within the same machine without hardware changes, reducing changeover time between pharmaceutical product codes.

⑥ PET / PETG / PP Multi-Material Compatible

Individually adjustable infrared heating zones support PET, PETG, and PP resins. The lower normal heating power range (8–12 kW) reflects the smaller container format — energy per preform is precisely metered rather than over-specified, reducing thermal overshoot risk at the 500 ml container scale.

Korea Ever-Power is a dedicated PET/PP blow molding machine manufacturer with over 20 years of focused R&D. Operating from a 20,000 m² production facility, Korea Ever-Power holds multiple national patents covering PET/PETG/PC/PCTG/PP multi-material packaging machinery and has earned international quality certifications including ECM Verification of Compliance.

Korea Ever-Power machines serve globally recognized brands across cosmetics, food & beverage, pharmaceutical, and daily-chemical sectors. Export destinations include Malaysia, Indonesia, Peru, Chile, Russia, Angola, Philippines, Norway, Morocco, Qatar, and more.

26–35 kg/cm² · 1,000–1,400 L/min · Lowest high-pressure air requirement in the ES medicine bottle range

8–10 °C · 30 L/min · Standard chiller sizing for 2-cavity 100 mm pitch mold cooling

7 kg/cm² · 600 L/min · Preform conveying and mold actuation at 100 mm pitch

What does the ES designation mean versus the AS series?

The ES series introduces Korea Ever-Power's servo-driven blow station architecture versus the earlier-generation AS series design. The ES machines provide more precise stretch-rod control, repeatable positioning across production runs, faster parameter changeover between bottle formats, and reduced mechanical wear in sustained high-output operation. The HGA.ES-2C100 is the entry-level ES series medicine bottle machine.

How does the HGA.ES-2C100 compare to the HGA.AS-2C114.3 at similar output?

Both are 2-cavity machines, but with different pitch and container ceiling. The ES-2C100 at 100 mm pitch supports up to 80 mm body / 68 mm neck / 500 ml; the AS-2C114.3 at 114.3 mm pitch supports up to 94 mm body / 88 mm neck / 1,000 ml. The ES-2C100 is smaller (2,000 kg vs 2,600 kg, 2,900 mm vs 2,660 mm length), runs lower utility requirements, and has slightly higher output (2,400 vs 2,000 BPH). Choose the AS-2C114.3 when your bottle requires >80 mm body diameter, >68 mm neck, or >500 ml volume.

What does the adjustable 26–35 kg/cm² blowing pressure range mean in practice?

Blowing pressure is set during commissioning based on the preform material, wall thickness target, and bottle geometry. The 26–35 kg/cm² range allows the machine to be tuned for different resin grades and bottle profiles without hardware changes — useful for pharmaceutical lines running PP bottles (which blow at lower pressure than PET) alongside standard PET or PETG vials on the same machine with mold changeover.

What is the floor load requirement for the HGA.ES-2C100?

At 2,000 kg on a 2,900 × 1,525 mm footprint, the floor load is approximately 452 kg/m² — lower than most other models in the Medicine Bottle Series and typically within standard factory and cleanroom floor load specifications without reinforcement. Confirm with a structural engineer before installation.

What compressed air system is required?

The HGA.ES-2C100 requires 1,000–1,400 L/min high-pressure air at 26–35 kg/cm² — the lowest high-pressure air requirement of the ES medicine bottle machines. An oil-free air compressor is mandatory for pharmaceutical-grade production. Low-pressure supply is 600 L/min at 7 kg/cm² for mold actuation and preform conveying.

Does Korea Ever-Power supply 100 mm pitch molds?

Yes. Korea Ever-Power designs and manufactures 2-cavity blowing molds at 100 mm pitch matched to the HGA.ES-2C100. Submit your bottle drawing — body diameter, neck finish, height, volume, and wall thickness targets — for a mold feasibility and pricing review. Preform injection molds for the 100 mm pitch format are also available as part of a complete supply package.

What after-sales support is included?

Korea Ever-Power provides on-site installation and commissioning, operator training, a one-year warranty on mechanical components, remote technical support via video call, and long-term spare parts availability. Regional service partners support customers in Malaysia, Indonesia, Peru, Chile, Russia, Philippines, Norway, Morocco, Qatar, and other export markets.

Which model should I choose if I need more than 2,400 BPH at 80 mm body diameter?

The next step up in the ES series for similar body dimensions is the HGA.ES-2C114.3 (2 cavities, 114.3 mm pitch, 2,000 BPH, up to 94 mm body / 1,000 ml) or the HGA.ES-3C76 (3 cavities, 3,000 BPH). For 4-cavity throughput at compact body formats, the HGA.ES-4C76 at 76 mm pitch delivers 4,800 BPH. Contact Korea Ever-Power with your output target and bottle specification for a direct model recommendation.

"We chose the ES-2C100 because our cleanroom floor space was the binding constraint. It fits without modification to our layout and the 2,400 BPH output meets our daily production target in a 1.5-shift operation. The smallest machine we've ever installed with this level of output quality."

HGA.ES-2C100

"We run PP and PETG vials on alternating shifts with mold changeover. The adjustable blowing pressure (26–35 kg/cm²) means we don't need separate machines for PP versus PET — we tune the pressure and swap the mold. This flexibility has made the ES-2C100 our most versatile production asset."

HGA.ES-2C100

"The compressor sizing was straightforward — 1,400 L/min at 35 kg/cm² is a much simpler specification than the larger machines. Our existing compressor could handle it after a minor upgrade. The machine commissioned in 3 days and we were at full production by the end of the first week."

HGA.ES-2C100

"Good wall thickness consistency at 2,400 BPH across our 75ml antiseptic bottles. Minor feedback: the 200mm max height limits us to our current product range and we'll need to upgrade when we introduce our 250ml format. Overall very happy with the compact footprint and easy maintenance access."

HGA.ES-2C100

"This is our second Korea Ever-Power machine — our first was a larger model. The ES-2C100 was installed for a new cleanroom line producing 100ml amber PETG pharmacy bottles. At 8–12 kW normal heating, the energy cost per thousand bottles is the lowest of any machine we operate. Very efficient for the output level."

HGA.ES-2C100

Get a Quote for the HGA.ES-2C100

Tell us your bottle body diameter, neck finish, height, volume, and required daily output. Our engineers will confirm 100 mm pitch compatibility and provide a machine and mold quotation within 2 business days.